Imagine being capable of body your personal pictures, prints, tapestries, and paintings in addition to a expert. Picture framing is clearly pretty amusing and clean to DIY. There are five easy steps to framing.
Step 1 – How to Cut Mats
Adding a shade border (the mat) round your artwork enhances the photo and provides a restful area between the photo and the photo body. The colour and length of the mat board must be determined first, as this may decide the overall dimensions of your image frame. You start by using calculating the outside size of the mat.
To cut the mat use a great excellent bevel mat cutter and ruler. There are several reducing systems to fit various budgets and skill tiers, such as the Mat Master Model 660 for the hobbyists, to the Mat Master 860B or 1060B for the eager home image framer.
Mark the borders to be reduce at the returned of the mat board.
Make sure the mat will cover the rims of the artwork, via subtracting approx. 3mm or 1/eight” from the picture size (duration & width). Cut the mat following the instructions on your mat cutter. Attach the picture to the mat the use of 2 small portions of acid unfastened tape at the pinnacle side handiest.
Step 2 – How to Cut the Picture Frame
How plenty photo frame moulding cloth will I need? Carefully degree the photograph and mat you desire to border. Add an extra (3mm) for “play” to make sure the image fits without problems into the finished image frame.
Add the period (L) and width (W) together, then multiply the overall by using 2 to present you the overall duration. You additionally need to allow for the mitre cuts, so multiply the width (W2) of the moulding by way of 10 and upload this on your overall.
(L + W) x 2 + (W2 x 10) = TOTAL
Making the 45 diploma mitre reduce in your framing fabric is most essential – your joining will best be as correct as your slicing. Always use an amazing best guide Mitre Saw… We advocate the Proman hand saw that is made in Sweden because the first-rate in the marketplace. Electric powered Drop Saws are not best for slicing small sensitive photograph frames.
Good Measure System helps to make measuring clean and removes many mistakes. Once you have got cut the primary mitre, slide the photograph frame cloth along to the desired length at the measuring scale, and set the prevent. You are actually prepared to reduce the primary 2 portions of your picture frame. Change the settings to reduce the opposite 2 sides of the body.
Cutting one facet for a body is simple.
Cutting the second side to be be similar to the primary, is the hard part. With the FrameCo Ezy-Measure System you can reduce as it should be every time.
Step three – How to Clamp Frames
How do you Clamp the Frame? Clamping the body tightly is critical for desirable joining. You can use the a Cord Clamp, or the Steel Strap Clamp to cozy the photo frame equipped for joining.
The gain of the Strap Clamp is that you can see all of the four corners of the photo body clamped together earlier than joining. So alignment of the corners is straightforward.
All corners must healthy up lightly. Apply a bit wood glue to all corners of the frame for brought strength. Carefully anxiety the clamp ensuring that the corners are aligned then comfy the clamp tightly.
You at the moment are prepared for joining.
Step 4 – How to Join Frames
Most image frames are joined with a V-Nail. This is the very best approach and it is what the expert photograph framer uses. The FrameCo PushMaster joining device, inserts V-Nails into the corner of the body. Two V-Nails in each nook is usually all this is essential.
The PushMaster can be used by hand alone on most photograph frames, or you could tap the PushMaster with a mallet if the body is hardwood. The PushMaster may be upgraded to the BenchMaster® if you want to insert V-Nails into the harderst of timbers.
V-nails: How do they paintings?
Upon access, the sides of the V-Nail are deflected outwards. As it pulls lower back into its authentic form, the join is pulled collectively. The little curl on the brink of the V-Nail locks the nail into the grain of the wood. Glue by myself isn’t always sufficient for strong solid joints, via including a V-Nail you achieve a sturdy, tight joint. Which V-Nail size . . . You use a V-Nail approximately 1/2 the body height.
Sizes are: 7mm – 1/four”, 10mm – 3/eight”, 12mm – 1/2″, 15mm – five/eight”
Step five – How to Finish Frames
Take the empty photograph frame to a pitcher merchant and have them cut a bit of glass for you. If you desire to reduce glass yourself use a very good nice oil crammed cutter, or the Glass Cutter. Use simplest 2mm simple or non-reflective glass.
Fome Core is the perfect backing board as it’s miles mild weight, acid free and clean to cut. You also can use 3mm MDF or cardboard. Place the empty frame face down and insert the glass, then the matted picture and ultimately the backing board.
Use the PushMaster to insert brads or flexipoints into the rear of your photograph body to hold the entirety in area.
Use Backing Nails for big frames or heavy items. Flexipoints are bendy and perfect for needlework or while you want to re move the photograph, eg. Photo frames.
To seal the art work in the frame, tape over the brads/flexipoints the use of a great best backing tape. This will save you dust or insects stepping into the photograph.